Messages
Below is a listing of messages, as they may appear in message dialog boxes.
A possible hardware issue exists. Please contact service.
A possible firmware issue exists. Re-install firmware. If problem persists, then contact service.
Scenario configuration has been modified. “Yes” allows you to specify a new scenario name to save it under. If “No” is selected, the current scenario name is used to save the configuration. “Cancel” does not start scenario execution and returns to previous menu.
Invalid coordinates given for scenario.
Invalid date or duration given for scenario.
General problem in scenario configuration when it is read into memory.
When setting duration to be “forever”, then navigation data/ephemeris setting must be on “Download”.
Scenario execution has encountered values that are too high. Simulated speed and altitude are limited in non-export GSG versions. Speed limit is 520 m/s and altitude is 18470 m. Change the scenario configuration.
Please review scenario settings. Restart GSG-5/6.
Please review scenario settings. Restart GSG-5/6.
Confirmation request before restoring factory defaults.
Configuring the Internet Protocol address failed. Please check your network settings and try again.
Saving of settings failed. Try restarting the device and saving parameters again. If it still fails, then please contact service.
The device was not able to use the configured parameters. Defaults are used in this case. Please go to the Menu and set the parameters again and store them with EXIT button.
Unit is not calibrated, or calibration data is corrupted. The device should be re-calibrated. Please contact service. Device can be used, but the observed power levels may differ from the ones shown in display.
Manual calibration data could not be saved. Restart unit and try again. If saving is still not possible, contact service.
The License file is corrupted. The device will work, but only as GSG-51. Contact service.
Confirmation for user calibration.
Calibration password entered is invalid. Try again.
After manual calibration you can choose to save or not save the values.
Unexpected problem occurred. Please restart the GSG-5/6.
GPS Start date is invalid in scenario configuration or signal generator. (Note: The earliest allowed start date is 6.1.1980.) Please check the date and correct it.
Check that selected navigation data file is a valid RINEX file (only version 2.1 and upwards supported).
Navigation data is not valid.
In the signal generator, navigation data is not found for the selected PRN and/or date. Try again with different values.
The navigation data file was missing when starting the signal generator. Select another option in the ephemeris list and try again.
External 10 MHz input is enabled, but no signal is detected. Connect the reference signal. If 10 MHz input is disabled and you still receive this message, contact service.
Mismatch detected between firmware components. Try to update the firmware. If you still receive the message contact service.
When giving name for a file, the name is empty. Please enter a file name.
Copying a directory is forbidden.
Removing a directory is forbidden.
Renaming directory is forbidden.
If this happens the device is faulty. Please contact service.
Confirmation request when removing file.
Removing of file fails.
Renaming a file failed. This condition may occur when there is no free storage space. Try removing any unnecessary files, and rename the file again.
Copying a file failed. This condition may occur when there is no free storage space. Try removing any unnecessary files, and copy the file again.
File is copied or renamed over an existing file. You can choose if you want to overwrite it or not.
The file for a given file manager operation (Copy, Rename or Delete) is performed is in use. You can choose whether to continue the operation or not. If the scenario in use is deleted, the current scenario becomes “None”.
This happens when the current scenario is “None” and scenario execution is started. Select a scenario to be executed.
Please review scenario settings. Restart GSG-5/6.
Restart GSG-5/6.
This message appears when there are no scenarios in the scenarios directory. Reset factory defaults to restore the default scenarios, or transfer your own scenarios from a PC using the StudioView software.
An unexpected problem has occurred while loading navigation data. Try scenario again. If problem persists, then contact service.
An unexpected problem has occurred while downloading and/or loading SBAS data. Try scenario again. If problem persists, then contact service.
Please review scenario settings. Restart GSG-5/6.
Saving of scenario settings failed. Try restarting the device and saving scenario configuration again. If it still fails, then please contact service.
Navigation/SBAS data download detected that the free storage space was too low. Please use Options > Manage files to free some space.
After reading in scenario file it was detected that field is invalid, therefore its value has been “capped” or set to a default valid value (for details, see Scenario File Format.)