T1/E1 Out Module [Option 13]

The E1/T1 option modules provide 1.544 MHz or 2.048 MHz and E1 or T1 data outputs for the NetClock platform (NetClock 9483 only).

NetClock meets G.812 Type I when installed with a Rubidium option, and G.811 when installed with a Rubidium option and synchronized with GNSS.

Note: Rubidium oscillators are recommended for the E1/T1 option module.

Module Option 13 E1/T1 (120 Ω): Specifications

• Outputs:
  • (1) 1.544/2.048 MHz RS-485 Outputs
  • (2) Balanced E1/T1Outputs
• T1 mode:
  • 1.544 MHz (square wave) frequency output
  • (2) 1.544 Mb/sec data rate outputs:
    • Outputs are DS1 framed all ones
    • Supports Super Frame (SF or D4) and Extended Super Frame (ESF)
    • SSM support
• E1 mode:
  • 2.048 MHz (square wave) frequency output
  • (2) 2.048 Mb/sec data rate outputs:
    • Outputs are E1 frame all ones
    • Supports CRC4 and CAS Multiframe
    • SSM support
• Connector and Signal Type: Terminal block
  • 1.544/2.048 MHz RS-485
  • T1 according to GR-499-CORE (100 Ω)
  • E1 according to ITU-T G703 (120 Ω)
• Maximum Number of Cards: 4
• Ordering Information: Option 13: T1/E1 (100/120 Ω) module

Option 13 T1/E1 module rear plate

Option 13 pin assignments

Pin Assignments
Pin No.	Signal	Function	Description
1	GND	Ground	Ground
2	1.544MHz/2.048MHz	RS-485 A Terminal	Square wave
3	1.544MHz/2.048MHz	RS-485 B Terminal	Square wave
4	GND	Ground	Ground
5	T1/E1 output A1	GR-499/G.703	Tip
6	T1/E1 output B1	GR-499/G.703	Ring
7	GND	Ground	Ground
8	T1/E1 output A2	GR-499/G.703	Tip
9	T1/E1 output B2	GR-499/G.703	Ring
10	GND	Ground	Ground

Model 1204-53 E1/T1 (75 Ω): Specifications

E1/T1 Output: Edit Window

To configure an E1/T1 data output , navigate to its Edit window. For instructions, see: Configuring Option Module Inputs/Outputs.

The Edit window allows the configuration of the following settings:

• Signature Control: Controls when the output will be present. For more information, see Signature Control.
• Mode: This option selects T1, E1, or disabled mode. For T1 mode, the clock output will be 1.544 MHz, and for E1 the clock output will be 2.048 MHz.
• SSM Enabled: Enables or disables Sync Status Messaging (SSM). T1 SSM is not valid with D4/Superframe or AIS framing. E1 SSM is not valid with AIS framing.
• E1 Encode: HDB3 only.
• E1 Framing: This option selects the framing standard (CRC-4, No CRC-4, or AIS).
• T1 Framing: This option selects the framing standard (D4/Superframe, Extended Superframe [CRC-6/no CR C-6], or AIS).
• T1 Encoding: This option selects the encoding method (B8ZS or AMI).
• T1SSM Value: This option selects the SSM quality level transmitted when SSM is enabled.
• E1 SSM Value: This option selects the SSM quality level transmitted when SSM is enabled.

E1/T1 Output: Status Window

To view the configuration settings of the E1 OUT or T1 OUT output, go to its Status window. For instructions, see: Viewing Input/Output Configuration Settings.

The E1/T1 Output 0 Status Screen will vary according to whether the output signal mode is E1 or T1.

The Status windows display the following settings:

• Signature Control: Controls when the output will be present; see Signature Control.
• Mode: This option selects T1, E1, or disabled mode. For T1 mode, the clock output will be 1.544 MHz, and for E1 the clock output will be 2.048 MHz.
• SSM Enabled: Enables or disables Sync Status Messaging (SSM). T1 SSM is not valid with D4/Superframe or AIS framing. E1 SSM is not valid with AIS framing.
• E1 Encoding: HDB3 only.
• E1 Framing: This option selects the framing standard (CRC-4, No CRC-4, or AIS).
• T1 Framing: This option selects the framing standard (D4/Superframe, Extended Superframe [CRC-6/no CR C-6], or AIS).
• T1 Encoding: This option selects the encoding method (B8ZS or AMI).
• T1 SSM Value: This option selects the SSM quality level transmitted when SSM is enabled.
• E1 SSM Value: This option selects the SSM quality level transmitted when SSM is enabled.